únava sila of high-strength bolts má vždy bol an dôležitý problém. Údaje ukazujú že väčšina z zlyhania z z vysokopevnostných skrutiek sú spôsobené únavou poškodením, a tam sú takmer nie znaky z skrutky počas únava poškodenie, so veľké nehody sú pravdepodobnosť na výskyt kedy únava poškodenie nastane.
So, plechovka teplo ošetrenie zlepšiť výkon z spojovací prvok materiály? ako veľa môže to zvýšiť jeho únava sila? v pohľad z zvýšenie použitie požiadavky z vysokopevnostných skrutiek, je vyrovnať viac dôležité zlepšiť únavu pevnosť of skrutky materiály cez teplo ošetrenie.
1. Material fatigue cracks of high-strength bolts:
The miesto kde únava praskliny prvý začiatok je volaný zdroj z únava. The únava zdroj je veľmi citlivý na mikroštruktúra z skrutky, a môže iniciovať únava trhliny na a veľmi malý mierka. Všeobecne v v 3 do 5 zrno veľkosti, the kvalita z the skrutka povrch je hlavný zdroj z únava, a najviac z únava začína od od povrch alebo podpovrchový of the skrutka. A veľký počet z dislokácie a niektoré legovanie prvky alebo nečistoty v skrutka materiál kryštál, a rozdiely v zrno hranica pevnosť, tieto faktory môže olovo do únava trhlina iniciácia. štúdie mať ukázať že únava trhliny sú náchylné na na hranice, povrch inklúzie alebo sekunda fáza častice, všetky zhruba ktoré sú súvisiace s spoločné komplexné a premenlivé mikroštruktúra z materiálov. Ak the mikroštruktúra môžem byť zlepšený po oteplení ošetrenie, únava pevnosť z skrutka materiál môže be zlepšený na a určitý rozsah.
2. Účinok z teplo liečba zapnutie únava sila
When analýza the únava sila of Skrutky, it is found that improving the static load bearing capacity of bolts can be achieved by increasing the hardness, but the improvement of fatigue strength cannot be achieved by increasing the hardness. Because the notch stress of the bolt will cause a large stress concentration, increasing the hardness of the sample without stress concentration can improve its fatigue strength. Hardness is an index to measure the softness and hardness of metal materials, and it is the ability of materials to resist the intrusion of objects harder than it. The level of hardness also reflects the strength and plasticity of metal materials. The stress concentration on the surface of the bolt will reduce its surface strength. When subjected to alternating dynamic loads, the process of micro-deformation and recovery will continue to occur at the stress concentration part of the notch, and the stress it receives is much greater than that of the part without stress concentration, so it is easy to lead to the formation of fatigue cracks.
3. Účinok of dekarbonizácia zapnutie únava sila
Decarburization of the bolt surface will reduce the surface hardness and wear resistance of the bolt after quenching, and significantly reduce the fatigue strength of the bolt. In the GB/T3098.1 standard, there is a decarburization test for bolt performance, and the maximum decarburization depth is specified. A large number of literatures show that due to improper heat treatment, the surface decarburization and surface quality of bolts are degraded, thereby reducing their fatigue strength. When analyzing the cause of fracture failure of high-strength bolts in 42CrMoA wind turbines, it was found that there was a decarburization layer at the junction of the head and rod. Fe3C can react with O2, H2O, and H2 at high temperature, resulting in the reduction of Fe3C inside the bolt material, thereby increasing the ferrite phase of the bolt material, reducing the strength of the bolt material, and easily causing microcracks. Controlling the heating temperature in the heat treatment process and using a controlled atmosphere to protect the heating can solve this problem well.
Spojovací materiály zlepšiť the mikroštruktúra cez teplo ošetrenie a temperovanie, a mať vynikajúci komplexný mechanické vlastnosti, ktorý môže zlepšiť únava pevnosť z skrutka materiály, rozumne kontrola zrno veľkosť na na zabezpečiť nízka teplota náraz energia, a tiež dosiahnuť vysoká náraz húževnatosť. rozumný teplo ošetrenie rafinuje zrná a skracuje zrno hranica vzdialenosť do predchádzať výskyt výskyt of únava praskliny. Ak tam je a určité množstvo z fúzy alebo sekunda častice vnútri materiál, tieto pridané fázy môže zabrániť obyvateľovi sklzu na a určitý rozsah. The sklz z pás predíde iniciácia a šírenie z mikrotrhlín.
Teplo ošetrenie má a veľký vplyv na únava pevnosť skrutka materiály. Počas teplo teplo ošetrenie proces, teplo ošetrenie proces 2c teplo ošetrenie proces by malo by stanovené podľa výkonu z skrutky The generácia počiatočná únava praskliny je spôsobené podľa stresu koncentrácia spôsobené podľa defektov v mikroštruktúre z skrutky materiálu materiálu. Teplo ošetrenie je a metóda na optimalizovať štruktúra z spojovacích materiálov, ktorý môže zlepšiť únava výkon z skrutka materiály na a určitý rozsah a zlepšiť životnosť z výrobkov. In the long run, it can save resources and conform to the strategy of sustainable development.






